he American Petroleum Institute specification API 5L X70 PSL2 Pipe covers seamless and welded steel line pipe.This is steel pipe for pipeline transportation systems in the petroleum and natural gas industries. API 5L is suitable for conveying gas, water, and oil. Size range is limited only by manufacturer’s capabilities.
Specifications for API 5L adhere to the International Organization for Standardization isO 3183, which standardizes pipeline transportation systems within the materials, equipment and offshore structures for petroleum, petrochemical, and natural gas industries.
The technical committee authoring the standards recognized that there are two basic Product Specifications Levels (PSL) of technical requirements and therefore developed PSL 1 and PSL 2. PSL 1 is a standard quality for line pipe where PSL 2 contains additional chemical, mechanical properties, and testing requirements.
Grades covered by this specification are A25 ,A ,B (and the following "X" Grades), X42, X46, X52, X56, X60, X65, X70, X80. The two digit number following the "X" indicates the Minimum Yield Strength (in 000's psi) of pipe produced to this grade.
Prosaic Steel Supply stocks a full range of API 5L X70 PSL-1 & PSL-2 line Pipe in seamless.
We can help supply all of the API 5L X70 PSL1 Pipe or linepipe supplies that your company needs for use in the oil or natural gas industries. API 5L Line Pipe Specifications for these pipes regulate usage for standard Grade A and Grade B pipes, with Grade X indicating stronger variants for drilling, production and transport requirements for offshore, arctic, deep well or harsher environments. Longitudinally welded steel pipes / Carbon Steel API 5L Gr. X70 PSL 2 Seamless Pipe are used in onshore and offshore oil and gas pipelines requiring critical service, high performance and tight tolerances.
All products are industry-standard conforming to or exceeding API, ASTM, ASME, ANSI and other national and international standards.
Whether you need Carbon Steel API 5L Gr. X42 Seamless Pipe, standard length and diameter pipes and tubing or you need high strength, high tensile, heavy wall linepipe requirements for deep sour wells, drilling, offshore drilling and production, arctic exploration and production, or you need Carbon Steel API 5L Gr. X70 PSL2 Seamless Pipefor natural gas, oil or water transport, then Prosaic Steel and Alloys. can meet the demands of your company.
Applications of API 5L X70 PSL2 Seamless Pipe
Carbon Steel is used in the most critical engineering applications and also in certain applications in the automotive sector. In addition, some of the value-added Carbon Steel products include steel for LPG cylinders, API grade, corrosion resistant steel, critical structural application steel, boiler quality, auto grades, precision tubes and medium/high carbon grades, among others.
Specification for line pipe API SPEC 5L (-09): specifies the requirements for the manufacture of two product specification levels (PSL1 and PSL2) of seamless and welded steel pipes for use in pipeline transportation systems in the petroleum and natural gas industries.
Mass fraction, based upon heat and product analysis % maximum | CARBON EQUIVALENT a | ||||||||||
% MAXIMUM | |||||||||||
Cb | Si | Mnb | P | S | V | Nb | Ti | Other | CEIIW | CEPcm | |
SEAMLESS & WELDED PIPES | |||||||||||
L485Q or X70Q | 0.18f | 0.45f | 1.8f | 0.025 | 0.015 | g | g | g | h | 0.43 | 0.25 |
WELDED PIPE | |||||||||||
L485M OR X70M | 0.12f | 0.45f | 1.7f | 0.025 | 0.015 | g | g | g | h | 0.43f | 0.25 |
Y.S | T.S | ELONGATION |
Mpa(psi) | Mpa(psi) | |
min | min | min |
485(70 300) | 635(92 100) | F |
IMPACT TEST | |
AVG. ABSORBED ENERGY | IND. ABSORBED ENERGY |
Min.(joules) | Min.(joules) |
27 | 20 |
Chemical composition for API 5L PSL 2 pipe with t ≤ 25,0 mm (0.984 in)
Steel grade (steel name) | Mass fraction, based upon heat and product analyses % maximum |
Carbon equivalenta % maximum |
|||||||||
C b | Si | Mn b | P | S | V | Nb | Ti | Other | CEiiw | CEpcm | |
Seamless and welded pipes | |||||||||||
L245R or BR | 0,24 | 0,40 | 1,20 | 0,025 | 0,015 | c | c | 0,04 | e | 0,43 | 0,25 |
L290R or X42R | 0,24 | 0,40 | 1,20 | 0,025 | 0,015 | 0,06 | 0,05 | 0,04 | e | 0,43 | 0,25 |
L245N or BN | 0,24 | 0,40 | 1,20 | 0,025 | 0,015 | c | c | 0,04 | e | 0,43 | 0,25 |
L290N or X42N | 0,24 | 0,40 | 1,20 | 0,025 | 0,015 | 0,06 | 0,05 | 0,04 | e | 0,43 | 0,25 |
L320N or X46N | 0,24 | 0,40 | 1,40 | 0,025 | 0,015 | 0,07 | 0,05 | 0,04 | d,e | 0,43 | 0,25 |
L360N or X52N | 0,24 | 0,45 | 1,40 | 0,025 | 0,015 | 0,10 | 0,05 | 0,04 | d,e | 0,43 | 0,25 |
L390N or X56N | 0,24 | 0,45 | 1,40 | 0,025 | 0,015 | 0,10f | 0,05 | 0,04 | d,e | 0,43 | 0,25 |
L415N or X60N | 0,24f | 0,45f | 1,40f | 0,025 | 0,015 | 0,10f | 0,05 | 0,04f | g,h | as agreed | |
L245Q or BQ | 0,18 | 0,45 | 1,40 | 0,025 | 0,015 | 0,05 | 0,05 | 0,04 | e | 0,43 | 0,25 |
L290Q or X42Q | 0,18 | 0,45 | 1,40 | 0,025 | 0,015 | 0,05 | 0,05 | 0,04 | e | 0,43 | 0,25 |
L320Q or X46Q | 0,18 | 0,45 | 1,40 | 0,025 | 0,015 | 0,05 | 0,05 | 0,04 | e | 0,43 | 0,25 |
L360Q or X52Q | 0,18 | 0,45 | 1,50 | 0,025 | 0,015 | 0,05 | 0,05 | 0,04 | e | 0,43 | 0,25 |
L390Q or X56Q | 0,18 | 0,45 | 1,50 | 0,025 | 0,015 | 0,07 | 0,05 | 0,04 | d,e | 0,43 | 0,25 |
L415Q or X60Q | 0,18f | 0,45f | 1,70f | 0,025 | 0,015 | g | g | g | h | 0,43 | 0,25 |
L450Q or X65Q | 0,18f | 0,45f | 1,70f | 0,025 | 0,015 | g | g | g | h | 0,43 | 0,25 |
L485Q or X70Q | 0,18f | 0,45f | 1,80f | 0,025 | 0,015 | g | g | g | h | 0,43 | 0,25 |
L555Q or X80Q | 0,18f | 0,45f | 1,90f | 0,025 | 0,015 | g | g | g | i,j | as agreed | |
Welded pipe | |||||||||||
L245M or BM | 0,22 | 0,45 | 1,20 | 0,025 | 0,015 | 0,05 | 0,05 | 0,04 | e | 0,43 | 0,25 |
L290M or X42M | 0,22 | 0,45 | 1,30 | 0,025 | 0,015 | 0,05 | 0,05 | 0,04 | e | 0,43 | 0,25 |
L320M or X46M | 0,22 | 0,45 | 1,30 | 0,025 | 0,015 | 0,05 | 0,05 | 0,04 | e | 0,43 | 0,25 |
L360M or X52M | 0,22 | 0,45 | 1,40 | 0,025 | 0,015 | d | d | d | e | 0,43 | 0,25 |
L390M or X56M | 0,22 | 0,45 | 1,40 | 0,025 | 0,015 | d | d | d | e | 0,43 | 0,25 |
L415M or X60M | 0,12f | 0,45f | 1,60f | 0,025 | 0,015 | g | g | g | h | 0,43 | 0,25 |
L450M or X65M | 0,12f | 0,45f | 1,60f | 0,025 | 0,015 | g | g | g | h | 0,43 | 0,25 |
L485M or X70M | 0,12f | 0,45f | 1,70f | 0,025 | 0,015 | g | g | g | h | 0,43 | 0,25 |
L555M or X80M | 0,12f | 0,45f | 1,85f | 0,025 | 0,015 | g | g | g | i | 0,43f | 0,25 |
L625M or X90M | 0,10 | 0,55f | 2,10f | 0,020 | 0,010 | g | g | g | i | --- | 0,25 |
L690M or X100M | 0,10 | 0,55f | 2,10f | 0,020 | 0,010 | g | g | g | i,j | 0,25 | |
L830M or X120M | 0,10 | 0,55f | 2,10f | 0,020 | 0,010 | g | g | g | i,j | 0,25 |
a Based upon product analysis. For seamless pipe with t > 20,0 mm (0.787 in), the carbon equivalent limits shall be as agreed. The CEiiw limits apply if the carbon mass fraction is greater than 0,12 % and the CEpcm limits apply if the carbon mass fraction is less than or equal to 0,12 %.
b For each reduction of 0,01 % below the specified maximum for carbon, an increase of 0,05 % above the specified maximum for manganese is permissible, up to a maximum of 1,65 % for grades ≥ L245 or B, but ≤ L360 or X52; up to a maximum of 1,75 % for grades >L360 or X52, but < L485 or X70; up to a maximum of 2,00 % for grades ≥L485 or X70, but ≤ L555 or X80; and up to a maximum of 2,20 % for grades >L555 or X80.
c Unless otherwise agreed, the sum of the niobium and vanadium concentrations shall be ≤ 0,06 %.
d The sum of the niobium, vanadium and titanium concentrations shall be ≤ 0,15 %.
e Unless otherwise agreed, 0,50 % maximum for copper, 0,30 % maximum for nickel, 0,30 % maximum for chromium and 0,15 % maximum for molybdenum.
f Unless otherwise agreed.
g Unless otherwise agreed, the sum of the niobium, vanadium and titanium concentrations shall be ≤ 0,15 %.
h Unless otherwise agreed, 0,50 % maximum for copper, 0,50 % maximum for nickel, 0,50 % maximum for chromium and 0,50 % maximum for molybdenum.
i Unless otherwise agreed, 0,50 % maximum for copper, 1,00 % maximum for nickel, 0,50 % maximum for chromium and 0,50 % maximum for molybdenum.
j 0,004 % maximum for boron.
9.2 Chemical compostion
9.2.4 For PSL 2 pipe with a product analysis carbon mass fraction equal to or less than 0,12 %, the carbon equivalent, CE pcm, shall be determined using Equation (2):
where the symbols for the chemical elements represent the mass fraction in percent (see Table 5).
.If the heat analysis for boron is less than 0,000 5 % then it is not necessary for the product analysis to include boron, and the boron content may be considered to be zero for the CEpcm calculation.
9.2.5 For PSL 2 pipe with a product analysis carbon mass fraction greater than 0,12 % the carbon equivalent, CEllw shall be determined using Equation (3):
where the symbols for the chemical elements represent the mass fraction in percent (see Table 5).
NOTE: A derogation from the isO rules for the presentation of chemical equations has been granted for Equations (2) and (3) in deference to their longstanding use in the industry.
Pipe grade | Pipe body of seamless and welded pipes | Weld seam of HFW, SAW and COW pipes | |||||
Yield strengtha Rto,5b MPa (psi) |
Tensile strengtha Rm MPa (psi) |
Ratioa,b,c Rto,5/Rm |
Elongation A f % |
Tensile strengthd Rm MPa (psi) |
|||
minimum | maximum | minimum | maximum | maximum | minimum | minimum | |
L245R or BR L245N or BN L245Q or BQ L245M or BM |
245 (35 500) |
450 e (65 300) e |
415 (60 200) |
760 (110 200) |
0,93 | f | 415 (60 200) |
L290R or X42R L290N or X42N L290Q or X42Q L290M or X42M |
290 (42 100) |
495 (71 800) |
415 (60 200) |
760 (110 200) |
0,93 | f | 415 (60 200) |
L320N or X46N L320Q or X46Q L320M or X46M |
320 (46 400) |
525 (76 100) |
435 (63 100) |
760 (110 200) |
0,93 | f | 435 (63 100) |
L360N or X52N L360Q or X52Q L360M or X52M |
360 (52 200) |
530 (76 900) |
460 (66 700) |
760 (110 200) |
0,93 | f | 460 (66 700) |
L390N or X56N L390Q or X56Q L390M or X56M |
390 (56 600) |
545 (79 000) |
490 (71 100) |
760 (110 200) |
0,93 | f | 490 (71 100) |
L415N or X60N L415Q or X60Q L415M or X60M |
415 (60 200) |
565 (81 900) |
520 (75 400) |
760 (110 200) |
0,93 | f | 520 (75 400) |
L450Q or X65Q L450M or X65M |
450 (65 300) |
600 (87 000) |
535 (77 600) |
760 (110 200) |
0,93 | f | 535 (77 600) |
L485Q or X70Q L485M or X70M |
485 (70 300) |
635 (92 100) |
570 (82 700) |
760 (110 200) |
0,93 | f | 570 (82 700) |
L555Q or X80Q L555M or X80M |
555 (80 500) |
705 (102 300) |
625 (90 600) |
825 (119 700) |
0,93 | f | 625 (90 600) |
L625M or X90M | 625 (90 600) |
775 (112 400) |
695 (100 800) |
915 (132 700) |
0,95 | f | 695 (100 800) |
L690M or X100M | 690 (100 100) |
840 (121 800) |
760 (110 200) |
990 (143 600) |
0,97 g | f | 760 (110 200) |
L830M or X120M | 830 (120 400) |
1 050 (152 300) |
915 (132 700) |
1 145 (166 100) |
0,99 g | f | 915 (132 700) |
Requirements for the results of tensile tests for PSL 2 pipe (continued)
a For intermediate grades, the difference between the specified maximum yield strength and the specified minimum yield strength shall be as given in the table for the next higher grade, and the difference between the specified minimum tensile strength and the specified minimum yield strength shall be as given in the table for the next higher grade, For intermediate grades lower than Grade L555 or X80, the tensile strength shall be ≤ 760 MPa (110 200 psl). For intermediate grades higher than Grade L555 or X80, the maximum permissible tensile strength shall be obtained by interpolation. For SI units, the calculated value shall be rounded to the nearest 5 MPa. For USC units, the calculated value shall be rounded to the nearest 100 psi.
b For grades >L625 or X90, Rp0,2 applies.
c This limit applies for pipe with D >323, 9 mm (12.750 in).
d For intermediate grades, the specified minimum tensile strength for the weld seam shall be the same value as was determined for the pipe body using footnote a).
e For pipe with D219,1 mm (8.625 in), the maximum yield strength shall be ≤495 MPa (71 800 psi).
f The specified minimum elongation, Af, shall be as determined using the following equation:
Where
C is 1 940 for calculations using SI units and 625 000 for calculations using USC units;
A xc is the applicable tensile test piece cross-sectional area, expressed in square millimeters (square inches), as follows:
---- for circular cross-section test pieces, 130 mm2 (0.20 in2) for 12,5 mm (0.500 in) and 8,9 mm (0.350 in) diameter test pieces; and 65 mm2 ( 0.10 in2) for 6,4 mm (0.250 in) diameter test pieces;
---- for full-section test pieces, the lesser of a) 485 mm2 (0.75 in2) and b) the cross-sectional area of the test piece, derived using the specified outside diameter and the specified wall thickness of the pipe, rounded to the nearest 10 mm2 (0.01 in2)
---- for strip test pieces, the lesser of a) 485 mm2( 0.75 in2 ) and b) the cross-sectional area of the test piece, derived using the specified width of the test piece and the specified wall thickness of the pipe, rounded to the nearest_10 mm2 (0.01 in2 );
U is the specified minimum tensile strength, expressed in megapascals (pounds per square inch).
g Lower Rto,5/Rm ratio values may be specified by agreement for L690 or X100 and L830 or X120 pipe.
Looking for a Carbon Steel API 5L Gr. X70 Seamless Pipe Supplier?
Carbon Steel Pipes and Tubes Products
A53 A106 API5L Grade B/C X42 Seamless Pipe
Size Range : 1/8" - 26"
Schedules : 20, 30, 40, Standard (STD), Extra Heavy (XH), 80, 100, 120, 140, 160, XXH
Grades : ASTM A53 Gr B, ASME SA53 Gr B, API-5L Gr B, ASTM A106 Gr B, ASME SA106 Gr B, ASTM A106 Gr C, PSL 1 and PSL2
API5L X-42 X-52 X-60 Seamless Pipe
Size Range : 2" - 24"
Schedules : Standard (STD), Extra Heavy (XH), 100, 120, 160, XXH
Grades : PSL1 and PSL2
A333 (Low Temp) Grade 1/6 Carbon Steel Seamless Pipe
Size Range : 1/2" - 24"
Schedules : Standard (STD), Extra Heavy (XH), 100, 120, 160, XXH
A53 API5L Grade B X-42 X-52 X-60 ERW (Electric Resistance Welded) Pipe
Size Ranges : 2" - 24"
Schedules : 10, 20, Standard (STD), Extra Heavy (XH)
Non-Schedules : .120wall, .156wall, .188wall, .203 wall, .219wall etc.
Grades : API-5L Gr B, API-5L Gr X42, API-5L Gr X52, API 5L X56, API-5L Gr X60, API-5L Gr X65, API 5L X70 PSL1 and PSL2
API5L Grade B X-42 X-52 X-60 DSAW/SAW
Size Ranges : 26" - 60"
Schedules : 20, Std, XH, 30,
Grades : API-5L Gr B, API-5L Gr X42, API-5L Gr X52, API 5L X56, API-5L Gr X60, API-5L Gr X65, API 5L X70 PSL1 and PSL2 Certified and Tesed NACE MR0175, NACE TM0177, NACE TM0284, HIC TEST, SSC TEST, SWC, H2 SERVICE, IBR, PWHT etc.
Sizes (Seamless): 1/2" NB - 60" NB
Sizes (ERW): 1/2" NB - 24" NB
Sizes (SAW): 16" NB - 100" NB
Wall Thickness available:
Schedule 20 - Schedule XXS (heavier on request) up to 250 mm thk
High Temperature Seamless Pipe | ASTM A106 Gr. B/C, API 5L Gr. B, ASTM A53 Gr. B |
Heat Exchanger Seamless Tube | ASTM A179 |
Low Temperature Seamless Pipe | ASTM A333 Gr. 3/6 |
Low Temperature Seamless Tube | ASTM A334 Gr. 6 |
High Yield Seamless Pipe | API 5L Gr. X42/X46/X52/X56/X60/X65/X70/X80 PSL-1/PSL-2 |
High Yield Seamless Pipe | ISO 3183 Gr. L245, L290, L320, L360, L390, L415, L450, L485 |
Atmospheric & Low Temp EFW Pipes | ASTM A671 Gr. CC60/CC65/CC70 |
High Pressure & Moderate Temp EFW Pipes | ASTM A672 Gr. B60/B65/B70/C55/C60/C65/C70 |
High Yield ERW/SAW Pipe | API 5L Gr. X42/X46/X52/X56/X60/X65/X70/X80 PSL-1/PSL-2 |
High Yield ERW/SAW Pipe | ISO 3183 Gr. L245, L290, L320, L360, L390, L415, L450, L485 |
Additional Testing for API 5L X70 PSL2 Seamless Pipe :
NACE MR0175, NACE TM0177, NACE TM0284, HIC TEST, SSC TEST, H2 SERVICE, IBR, etc.
Dimensions for API 5L X70 PSL1 Seamless Pipe:
All Pipe is manufactured and inspected/tested to the relevant standards including ASTM, ASME, API.
API 5L Grade B PSL1 Line Pipes - Available ex-stock
API 5L Grade B PSL2 Line Pipes - Available ex-stock
API 5L Grade B PSL1 Sour Service Line Pipes - Available ex-stock
API 5L Grade B PSL2 Sour Service Line Pipes - Available ex-stock
API 5L Grade B PSL1 NACE MR-0175 Line Pipes - Available ex-stock
API 5L Grade B PSL2 NACE MR-0175 Line Pipes - Available ex-stock
API 5L X42 PSL1 Line Pipes - Available ex-stock
API 5L X42 PSL2 Line Pipes - Available ex-stock
API 5L X42 PSL1 Sour Service Line Pipes - Available ex-stock
API 5L X42 PSL2 Sour Service Line Pipes - Available ex-stock
API 5L X42 PSL1 NACE MR-0175 Line Pipes - Available ex-stock
API 5L X42 PSL2 NACE MR-0175 Line Pipes - Available ex-stock
API 5L X46 PSL1 Line Pipes - Available ex-stock
API 5L X46 PSL2 Line Pipes - Available ex-stock
API 5L X46 PSL1 Sour Service Line Pipes - Available ex-stock
API 5L X46 PSL2 Sour Service Line Pipes - Available ex-stock
API 5L X46 PSL1 NACE MR-0175 Line Pipes - Available ex-stock
API 5L X46 PSL2 NACE MR-0175 Line Pipes - Available ex-stock
API 5L X52 PSL1 Line Pipes - Available ex-stock
API 5L X52 PSL2 Line Pipes - Available ex-stock
API 5L X52 PSL1 Sour Service Line Pipes - Available ex-stock
API 5L X52 PSL2 Sour Service Line Pipes - Available ex-stock
API 5L X52 PSL1 NACE MR-0175 Line Pipes - Available ex-stock
API 5L X52 PSL2 NACE MR-0175 Line Pipes - Available ex-stock
API 5L X56 PSL1 Line Pipes - Available ex-stock
API 5L X56 PSL2 Line Pipes - Available ex-stock
API 5L X56 PSL1 Sour Service Line Pipes - Available ex-stock
API 5L X56 PSL2 Sour Service Line Pipes - Available ex-stock
API 5L X56 PSL1 NACE MR-0175 Line Pipes - Available ex-stock
API 5L X56 PSL2 NACE MR-0175 Line Pipes - Available ex-stock
API 5L X60 PSL1 Line Pipes - Available ex-stock
API 5L X60 PSL2 Line Pipes - Available ex-stock
API 5L X60 PSL1 Sour Service Line Pipes - Available ex-stock
API 5L X60 PSL2 Sour Service Line Pipes - Available ex-stock
API 5L X60 PSL1 NACE MR-0175 Line Pipes - Available ex-stock
API 5L X60 PSL2 NACE MR-0175 Line Pipes - Available ex-stock
API 5L X65 PSL1 Line Pipes - Available ex-stock
API 5L X65 PSL2 Line Pipes - Available ex-stock
API 5L X65 PSL1 Sour Service Line Pipes - Available ex-stock
API 5L X65 PSL2 Sour Service Line Pipes - Available ex-stock
API 5L X65 PSL1 NACE MR-0175 Line Pipes - Available ex-stock
API 5L X65 PSL2 NACE MR-0175 Line Pipes - Available ex-stock
API 5L X70 PSL1 Line Pipes - Available ex-stock
API 5L X70 PSL2 Line Pipes - Available ex-stock
API 5L X70 PSL1 Sour Service Line Pipes - Available ex-stock
API 5L X70 PSL2 Sour Service Line Pipes - Available ex-stock
API 5L X70 PSL1 NACE MR-0175 Line Pipes - Available ex-stock
API 5L X70 PSL2 NACE MR-0175 Line Pipes - Available ex-stock
API 5L X80 PSL1 Line Pipes - Available ex-stock
API 5L X80 PSL2 Line Pipes - Available ex-stock
API 5L X80 PSL1 Sour Service Line Pipes - Available ex-stock
API 5L X80 PSL2 Sour Service Line Pipes - Available ex-stock
API 5L X80 PSL1 NACE MR-0175 Line Pipes - Available ex-stock
API 5L X80 PSL2 NACE MR-0175 Line Pipes - Available ex-stock
Inspection & Approval Certificates : EN10204 3.1 / DIN 50049 3.1 / isO 10474 3.1 Mill Test Certificate, NACE MR-0175 / isO 15156, NACE MR-01-03 / NACE MR-01-75 / isO 15156, CE Marked, European Pressure Equipment Directive PED-97/23/EC, AD-2000-W0, ASME Boiler & Pressure Vessel Code Sec.II Part A Ed. 2008, with 3.2 certificate duly Certified & Approved by LRS (Lloyd's Register), GL (Germanischer Lloyd), BV (Bureau Veritas), DNV (Det Norske Veritas), ABS (American Bureau of Shipping), SGS, TUV, RINA, IRS, NORSOK Approved Standard M-630, M-650 Rev.3
API 5L Grade x 70 PSL 2 Pipes, best quality API 5L Grade x 70 PSL 2 Pipes,, wide variety of API 5L Grade x 70 PSL 2 Pipes, API 5L Grade x 70 PSL 2 Pipes, India, API 5L Gr.B PSL1/1 Pipes distributor Mumbai, API 5L Grade x 70 PSL 2 Pipes, traders, prime quality API 5L Grade x 70 PSL 2 Pipes, Pipes, Source for API 5L Grade x70 PSL 2 Pipes,, specialize in API 5L Grade x 70 PSL 2 Pipes,, API 5L Grade x 70 PSL 2 Pipes, with Test Certificate
API 5L X70 PSL2 Pipe is sleeved into plastic bag individually, pieces wrapped with water-proof material, bundled with nylon rope. Clear labels are tagged on the outside of the package for easy identification of the quantity and product I.D. Great care is taken during operation and transportation.
API 5L X70 PSL2 Carbon Steel Seamless Pipe packing will be according to international standard in bundles strapped by strips then into containers to avoid any damage.
Delivery: Within 10-25 days or asap if we have enough stock
We export API 5L X70 PSL2 Pipe to Saudi Arabia, Iran, Iraq, United Arab Emirates, Qatar, Bahrain, Oman, Kuwait, Turkey, Egypt, Yemen, Syria, israel, Jordan, Cyprus, Singapore, Malaysia, Indonesia, Thailand, Vietnam, South Korea, Japan, Sri Lanka, Maldives, Bangladesh, Mayanmar, Taiwan, Cambodia, Argentina, Bolivia, Brazil, Chile, Venezuela, Colombia, Ecuador, Guyana, Paraguay, Uruguay, United States Of America, Canada, Mexico, Panama, Costa Rica, Puerto Rica, Trinidad And Tobago, Jamaica, Bahamas, Denmark, Russia, Norway, Germany, France, Italy, United Kingdom, Spain, Ukraine, Netherland, Belgium, Greece, Czech Republic, Portugal, Hungary, Albania, Austria, Switzerland, Slovakia, Finland, Ireland, Croatia, Slovenia, Malta, Nigeria, Algeria, Angola, South Africa, Libya, Egypt, Sudan, Equatorial Guinea, The Republic Of Congo, Gabon, Europe, Africa, Asia, North America, South America, Middle East, Far East.etc.
Prosaic Steel and Alloys is a well known worldwide exporter of API 5L X70 PSL2 Pipe, Prosaic Steel and Alloys is committed to provide each and every customer with the highest standard of customer service. We deals in API 5L X70 PSL2 Pipe in India & Overseas, offering a wide range of API 5L X70 PSL2 Pipe.
Prosaic Steel and Alloys is Leading Manufacturer, Distributor, Exporter, Stockholder and Supplier of API 5L X70 PSL 2 Pipe in United States of America (USA), Saudi Arabia, Italy, Netherlands, Germany, Canada, Singapore, Malaysia, Indonesia
api 5l x70 chemical composition, api 5l x70 especificaciones, aço api 5l x70, api 5l pipe schedule, api 5l pipe weight chart, api 5l pipe supplier, api 5l PIPE MANUFACTURER, api 5l pipe thickness table, api 5l x60 psl2, api 5l x65 psl2, api 5l x70 chemical composition, api 5l x70 psl2 specification, api 5l x70 properties,x70 pipe specifications, api 5l pipe price list, api 5l x70 specificaciones
API 5L X70 Pipe, API 5L X70 PSL1 Pipe, API 5L X70 PSL2 Pipe, API 5L X70 Line Pipe, API 5L X70 Carbon Steel Pipe
We provide API 5L X70 Pipe with PSL1 and PSL2. We Carry Complete Range from 02" NB to 24" NB, wall Thickness upto 100 MM. Prosaic Steel and Alloys API 5L X70 Pipe are known for its High Quality and Competitive Price.
API 5L X70 PSL 2 Pipe